Improved machining accuracy of hollow cylinder components based on preventive compensation for tool wear errors
https://doi.org/10.21285/1814-3520-2025-2-184-193
EDN: MOQKFJ
Abstract
Objective – improvement of the precision of finish reaming of hollow cylinder type components by using preventive compensation for cutting tool wear. The study focuses on hollow cylinder type components, exemplified by the liners of drilling pump cylinders, where the finish machining of the central bore is studied. The machining is performed on a numerically controlled lathe. The proposed approach involves dynamic monitoring of the cutting-edge condition during the production of a test batch. The cutting blade is described as a set of points that subsequently approximate the contour of the cutting edge. Since the wear pattern of each individual insert is random, the study uses an artificial intelligence approach to solve the prediction problem. A neuro-fuzzy model was developed to describe the cutting edge during wear. The model includes a knowledge base that is updated based on the monitoring results of the cutting edge shape. The model also includes a logical block containing a set of conditions that enable the simulation results to be produced with the required accuracy. Testing of the developed model shows that the error in describing the cutting edge contours does not exceed 8%. On the basis of the calculated descriptions of the blade contour, corrections to the cutting tool trajectories are calculated, which allow compensation for the wear of the cutting plate. Research into the effectiveness of the solutions obtained has shown that it is possible to increase tool efficiency (in terms of tool life) by 35–45%. In addition, the developed neuro-fuzzy model can be integrated into an expert system that helps to reduce the risk of sudden cutting tool failure. This is particularly important in the manufacture of hydraulic machine components.
About the Authors
V. E. Ovsyannikov
Industrial University of Tyumen
Russian Federation
Russian Federation
Viktor E. Ovsyannikov, Dr. Sci. (Eng.), Associate Professor, Professor of the Department of Mechanical Engineering Technology
38 Volodarsky St., Tyumen 625000
R. Yu. Nekrasov
Industrial University of Tyumen
Russian Federation
Russian Federation
Roman Yu. Nekrasov, Cand. Sci. (Eng.), Associate Professor, Head of the Department of Mechanical Engineering Technology
38 Volodarsky St., Tyumen 625000
S. S. Chuikov
Industrial University of Tyumen
Russian Federation
Russian Federation
Sergey S. Chuikov Cand. Sci. (Eng.), Associate Professor, Head of the Department of Metal-Cutting Machines
38 Volodarsky St., Tyumen 625000
E. M. Kuznetsova
Kurgan State University
Russian Federation
Russian Federation
Elena M. Kuznetsova, Cand. Sci. (Eng.), Senior Lecturer of the Department of Industrial Process Automation
63/4 Sovetskaya St., Kurgan 640669
References
1. Gasanov B.G., Sirotin P.V., Ismailov M.A., Harchenko E.V. Improving the shock-abrasive wear resistance of mud pump valve parts. Scientific Research: Results and Prospects. 2023;4(1):39-44. (In Russ.). https://doi.org/10.21822/2713-220X-2023-4-1-39-44. EDN: LCBCWX.
2. Иванов Е.А., Иванова О.В., Грицына Н.И. Production of bimetallic sliding bearings for drilling pumps in conditions venture firm Poisk LLP. Vestnik of M. Kozybayev North Kazakhstan University. 2022;3:149-158. (In Russ.). https://doi.org/10.54596/2309-6977-2022-3-149-158. EDN: YLGEIK.
3. Yurochkin S.B., Pavlov A.I., Kisel’nikova L.V. Drilling pump piston. Patent RF, no. 24529; 2002. (In Russ.). EDN: CQANWN.
4. Makushkin D.O., Murashko A.F., Davydov A.V. Mud pump valve. Patent RF, no. 117553; 2012. (In Russ.). EDN: MOGFQR.
5. Fairushin R.F. Single-acting three-piston drilling pump. Patent RF, no. 2770342; 2022. (In Russ.). EDN: EELKXO.
6. Urals Machine-Building Plant. Pump for a drilling rig. Patent RF, no. 30383; 2003. (In Russ.). EDN: NIXYSO.
7. Smirnova E.N., Krylov E.G. Issues of technological process computer-aided design based on technological heredity. Bulletin of the Technological University. 2011;13:100-102. (In Russ.). EDN: ONCNMF.
8. Kotlyarov V.P., Maslakov A.P., Tolstoles A.A. Digital modelling of production engineering for metalworking machine shops. Proceedings of the Institute for System Programming of the RAS. 2019;31(3):85-98. https://doi.org/10.15514/ISPRAS-2019-31(3)-8. EDN: LSIJGC.
9. Pukhov A.S. Organizational, technical and environmental principles for automated system creation. In: Bezopasnost’ zhiznedeyatel’nosti: problemy i resheniya – 2017: materialy mezhdunarodnoi nauchno-prakticheskoi konferentsii = Life Safety: Problems and Solutions - 2017: Proceedings of the International scientific and practical conference. 25–26 May 2017, Lesnikovo. Lesnikovo: Kurgan State Agricultural Academy named after T.S. Maltsev; 2017, 336-342. (In Russ.). EDN: YQQXKK.
10. Karlina Yu.I. Integration of stages of preparation of production of high-precision small parts on CNC machines. Modern technologies. System analysis. Modeling. 2021;1:17-23. (In Russ.). https://doi.org/10.26731/1813-9108.2021.1(69).17-23. EDN: WQHCPV.
11. Artamonov E.V., Tveryakov A.M., Shtin A.S. Investigation of electromagnetic properties of tool hard alloys under the influence of high temperatures. In: Materials Research Proceedings. 6–10 September 2021, Temryuk. Temryuk; 2022, р. 323-328. https://doi.org/10.21741/9781644901755-57. EDN: ZBJDOB.
12. Kabaldin Yu.G., Sablin P.A., Shchetinin V.S. Control of the dynamic stability of metal-cutting systems in the process of cutting based on the fractality of roughness of the machined surface. Frontier Materials & Technologies. 2023;3:43-51. (In Russ.). https://doi.org/10.18323/2782-4039-2023-3-65-4.
13. Kabaldin Yu.G., Ivanov S.V., Bashkov A.A. Tribosystem stability control under external friction and cutting based on the algorithms of nonlinear dynamics, fractal theory and neural network modeling. Mekhatronika, avtomatika i robototekhnika. 2024;13:150-156. (In Russ.). https://doi.org/10.26160/2541-8637-2024-13-150-156. EDN: NXFIAU.
14. Zakovorotnyi V.L., Gvindjiliya V.E. Influence of speeds of forming movements on the properties of geometric topology of the part in longitudinal turning. Journal of Manufacturing Processes. 2024;112:202-213. https://doi.org/10.1016/j.jmapro.2024.01.037. EDN: LHVZHV.
15. Bezyazychnyy V.F., Palamar’ I.N. Current aspects in automation of scientific researches of machinery surface quality using machine learning methods. Science intensive Technologies in Mechanical Engineering. 2021;7:12-19. (In Russ.). https://doi.org/10.30987/2223-4608-2021-7-12-19. EDN: VIPEMD.
16. Artamonov E., Vasilega N., Yadygin A. Analysis of factors affecting operability to assess risks and opportunities in the operation of built-up cutting tools. Key Engineering Materials. 2022;910:220-225. https://doi.org/10.4028/p-wu7wdy.
17. Zakovorotny V., Gvindjiliya V. The features of the evolution of the dynamic cutting system due to the regenerative effect. In: Dynamics of technical systems: AIP Conference Proceedings of the 7 International Scientific-Technical Conference. 9–11 September 2023, Rostov-on-Don. Rostov-on-Don: American Institute of Physics Inc.; 2023, vol. 2507, Iss. 1, Р. 030002. https://doi.org/10.1063/5.0109559. EDN: FLSYFX.
18. Ovsyannikov V., Nekrasov R., Putilova U., Il’yaschenko D., Verkhoturova E. On the issue of automatic form accuracy during processing on CNC machines. Revista Facultad de Ingenieria. 2022;103:88-95. https://doi.org/10.17533/udea.redin.20201111. EDN: HCVDFL.
19. Stupnytskyy V., Dragašius E., Baskutis S., Xianning Sh. Modeling and simulation of machined surface layer microgeometry parameters. Ukrainian Journal of Mechanical Engineering and Materials Science. 2022;8(1):1-11. (In Russ). https://doi.org/10.23939/ujmems2022.01.001. EDN: FGAHMG.
20. Proskuryakov N.A., Nekrasov R.Y., Starikov A.I., Solov’ev I.V., Barbyshev B.V., Tempel’ Y.A. Fuzzy controllers in the adaptive control system of a CNC lathe. Russian Engineering Research. 2018;38(3):220-222. https://doi.org/10.3103/S1068798X18030188. EDN: XXMQTZ.
21. Tempel Yu.A., Nekrasov R.Yu., Tempel O.A. Simulation of the influence of cutting forces on the part geometry and algorithm for automation of correction of the control program. Izvestiya Tul’skogo gosudarstvennogo universiteta. Technical Sciences. 2022;4:533-537. (In Russ.). https://doi.org/10.24412/2071-6168-2022-4-533-538. EDN: JKPXBZ.
Review
For citations:
Ovsyannikov V.E., Nekrasov R.Yu., Chuikov S.S., Kuznetsova E.M. Improved machining accuracy of hollow cylinder components based on preventive compensation for tool wear errors. iPolytech Journal. 2025;29(2):184-193. (In Russ.) https://doi.org/10.21285/1814-3520-2025-2-184-193. EDN: MOQKFJ
Views:
92
Email this article 